Dometic RM 4223 Instrukcja Użytkownika Pobierz pdf

REVISION

Form No. 3107479.036 11/97

(Replaces 3107479.028)

LaGrange, IN 46761

VENT INSTALLATION INSTRUCTIONS

FOR DOMETIC REFRIGERATORS

As Required by the American/Canadian Gas Associations

This Manual should be read and under-

stood before installation, adjustment,

service or maintenance is performed.

This unit must be installed and serviced

by a qualified serviceman. Modification

of this appliance can be extremely haz-

ardous and could result in personal

injury or property damage.

1. GENERAL INSTRUCTIONS

The vents outlined herein have been design certified by

A.G.A. under ANSI Z21.19 Refrigerator Standard for instal-

lation in a mobile home or recreational vehicle and are

approved by the Canadian Gas Association.

The certifications are, however, contingent on the

installation being made in accordance with the following

instructions as applicable.

In the U.S.A., the installation must conform with:

1. National Fuel Gas Code ANSI Z223.1 (latest edition)

2. Manufactured Home Construction and Safety Stan-

dard, Title 24 CFR, Part 3280

3. Recreational Vehicles ANSI A119.2 (latest edition)

The unit must be electrically grounded in accordance with

the National Electric Code ANSI/NFPA 70 (latest edition)

when installed if an external alternating current electrical

source is utilized.

4. Any applicable local code.

In Canada, the installation must conform with:

1. Current CGA B 149 Gas Installation Codes

2. Current CSA Standard Z240.4 GAS-EQUIPPED REC-

REATIONAL VEHICLES AND MOBILE HOUSING

3. Any applicable local code

2. VENTILATION

The installation shall be made in such a manner as to

separate the combustion system from the living space of

the mobile home or recreational vehicle. Openings for air

supply or for venting of combustion products shall have a

minimum dimension of not less than 1/4 inch.

All joints in the enclosure must be sealed to

prevent gas leakage into the living area. Clear-

ance from the combustible materials must be

maintained as shown in the cross-section views.

Proper installation requires one fresh air intake and one

upper exhaust vent. The ventilation kits shown in this

instruction manual have been certified for use with the

refrigerator model listed in the Table. For refrigerator vent

options, see Page 11. The ventilation kits must be installed

and used without modification. An opening toward the

outside at floor level in the refrigerator compartment must

be provided for ventilation of heavier-than-air fuel gases.

The lower vent of the recommended kits is provided with

proper size openings. The flow of combustion and ventila-

tion air must not be obstructed.

The lower side vent is fitted with a panel which provides an

adequate access opening for ready serviceability of the

burner and control manifold of the refrigerator. This should

be centered on the back of the refrigerator.

When installing the refrigerator, the installer must block the

space between the storage cabinet and the top of the

refrigerator, otherwise heat will become trapped in this

space, making the top of the refrigerator hot, thus reducing

the efficiency of the unit.

For additional instructions not covered in this manual, see

Installation Instructions for the model of refrigerator being

installed.

3. CERTIFIED INSTALLATIONS

All options must have both an upper and lower side

vent, or a roof vent matched with a lower vent.

4. METHODS OF INSTALLATION

OPTION NO. 1

Consists of one roof vent and one lower side vent.

Recommended for normal installations where

natural draft ventilation is possible.

OPTION NO. 2

Consists of two side vents.

Natural draft ventilation on smaller single-door

models where Installation Option No. 1 is NOT

possible.

1 2 3 4 5 6 ... 12 13

Podsumowanie treści

Strona 1 - LaGrange, IN 46761

Strona 2 - OPTION 1

10APPROVED DOMETIC REFRIGERATOR VENTSVENT NO. 7THE INNOVATOR REFRIGERATORVENTILATION SYSTEMFor Use with Single Door RefrigeratorsVENT NO. 8THE INNOVAT

Strona 3 - OPTION 2

11 VENT VENT VENT VENT VENTOPTIONOPTIONOPTIONOPTIONOPTIONOPTIONOPTIONOPTIONOPTIONOPTIONOPTIONOPTIONOPTIONOPTIONOPTIONOPT

Strona 4 - Ventilation System

12RM2612RM2812RM2852RM3662RM3663REFRIGERATOR VENT OPTIONS(For Description of Option, See Page 1, #4 Methods of Installation) VENT VENT

Strona 5

13RM3862RM3863RM4872RM4873RM7732RM7832REFRIGERATOR VENT OPTIONS(For Description of Option, See Page 1, #4 Methods of Installation)* NOTE: Vent Number

Strona 6

2Model No. A* B C D *** E F** GRM2310 31 21-3/8 29-3/4 20-1/2 8 1 1RM2410 34 24 32-7/16 21-3/16 8 0 1RM2452 37-3/4 24 36-9/16 23-11/16 8 0

Strona 7

3Model No.A*BCDEF**GRM2193(1) 20-5/8 20-7/8 20-7/8 17-3/4 4 1 1RM2193(2) 21-5/8 20-7/8*** 20-7/8 17-3/4 4 1 1RM2202(1) 23 18 22-1/4 19-5/8 4 1 1RM2202

Strona 8

4 ACCESS PANELMODEL DIMENSIONSERIES A BRM2612, RM3662, RM3663 22" 14"RM2812, RM2652RM2852,RM3862, RM3863,RM4872, RM4873, ND

Strona 9

5OPTION 3The Innovator Refrigerator Ventilation SystemB. THE INNOVATOR VENTILATION SYSTEM FOR SINGLE DOOR ABSORPTION REFRIGERATORSWITH TWO SIDE VENTS.

Strona 10 - VENT NO. 10

6OPTION 3The Innovator Refrigerator Ventilation SystemC. INNOVATOR VENTILATION SYSTEM FOR SINGLE DOOR REFRIGERATORSWITH 2 PLASTIC SIDE VENTSThe Innova

Strona 11 - REFRIGERATOR VENT OPTIONS

7OPTION 3The Innovator Refrigerator Ventilation SystemD. INNOVATOR VENTILATION SYSTEM FOR DOUBLE DOOR REFRIGERATOR WITH 2 SIDE VENTSThe power ventilat

Strona 12

8OPTION 3The Innovator Refrigerator Ventilation SystemE. INNOVATOR VENTILATION SYSTEM FOR SIDE-BY-SIDE REFRIGERATOR WITH 2 SIDE VENTSThe Innovator Ven

Strona 13

9APPROVED DOMETIC REFRIGERATOR VENTSVENT NO. 1DOMETIC PLASTIC ROOF VENTVENT NO. 2DOMETIC PLASTIC SIDE VENTVENT NO. 3DOMETIC UPPER SIDE VENTVENT NO. 4D